Hardware




[+] Larger

Glide Pak Multi Track 25

[ ]

The Camfil Farr GlidePack MultiTrack 25 is a multi-stage air filter housing with adaptable tracks to apply a variety of prefiltration, secondary filtration that may include adsorbers, and final filtration to provide superior indoor air quality for virtually any application. The housing may also be reconfigured in the field for air filtration upgrades or to adapt to the latest air filtration technology. The aluminum air filter mounting track includes ribbed surfaces to ensure that filters slide easily across the tracks in housing configurations from four high to six filters wide. The tracks include slide modifiers that may be moved or removed to change filter configurations to accommodate a 2” or 4” deep prefilter, a 2”, or 4” deep intermediate particulate or carbon filter, and a 6” or 12” deep rigid or pocket final filter. Each Camfil Farr GlidePack MultiTrack includes:



Spec Sheet
Sizes | Buy


[+] Larger

CamCarb Cylinder SMH Glide/Pack

[ Housings ]

• Combines high capacity sorbent canisters with side-access housings for low bypass large system gaseous contaminant control.
• Side-access housing integrity with dual access doors may be up to four filters high by six filters wide.

Typical applications: HVAC system installation in commercial, industrial, manufacturing and medical facilities.
Construction: 16-gauge aluminized steel, gasketed dual access doors, anodized aluminum filter tracks for 2" deep prefilters and separate track for CamCarb Cylinders. Consult factory for stacking and reinforcement guidelines.
Filters: Accepts 2" deep particle prefilter and 16 CamCarb Cylinders per 24" by 24" opening.
Additional data: Out-turned pre-drilled standing flanges mate to other HVAC equipment.



Spec Sheet
Sizes | Buy


[+] Larger

Farr Fasteners

[ ]

Camfil Farr fastener ~ are available for built-up bank holding frames or housings that incorporate frames to ensure that air filters fit securely in the holding mechanism.A gap around a 24” by 24” filter may result in as much as 18% air bypass, or the equivalent of a 3” hole in the middle of the filter. The use of the correct fastener, and the proper number of fastener, ensures that the air moving through the system will be wholly treated by the air filters ensuring improved indoor air quality for the facility. ~ Camfil Farr fastener are: ~ available in many different variations ~ configurations available for Camfil Farr holding frames or holding frames by other manufacturers ~ standard construction of high tensile strength steel or cad-plated in many configurations ~ available in stainless steel ~ may be combined to apply up to four stages of filtration.



Spec Sheet
Sizes | Buy


[+] Larger

Magna Hepa Frames

[ ]

The Camfil Farr Magna-Frame is an individual holding frame designed to ensure that the system efficiency equals the filter efficiency. The Magna-Frame: • Is constructed of all-welded 14-guage galvanized steel (also available in 304SST). The frame will withstand 30 inch/lb. of sealing torque on the filter element at differentials greater than 10” w.g. without distortion. Sealing integrity is further ensured through the use of welded mitered corners. • Includes a 1” absolute filter sealing flange to ensure an airtight filter gasket to frame seal. • Includes annular-based dimples for proper filter alignment. Filter changes are simplified as the filter is centered within the holding frame. • Includes pre-punched assembly holes for quick and easy assembly. The holes are within the annular dimples to recess assembly bolts or rivets. • Incorporates vertical side swing bolt assemblies with equi-bearing clamps to provide uniform filter sealing pressure. • Is available with an optional absolute prefilter kit that allows the installation of an absolute filter, ASHRAE high efficiency filter, and prefilter in one assembly. Absolute filter integrity is not compromised during prefilter service.



Spec Sheet
Sizes | Buy


[+] Larger

Magna Hepa Frames

[ ]

Absolute Prefilter Kits - Prefilter Kits for Absolute Built-up Bank Installations Camfil Farr Absolute Prefilter Kits allow installation of Camfil Farr's wide variety of prefilters in front of absolute filters as installed in Camfil Farr’s Magna Frame I/II/III holding frames or Magna-Grid built-up bank systems. The kits include the Camfil Farr Type 8 frame (for full‑size), or an adapter frame (for undersized), and swing bolt assemblies to install one or two stages of prefiltration upstream of the absolute filters. All standard features are incorporated, including a 3/4" sealing flange, factory applied polyurethane foam gasket, dimples which automatically center the filters and lances for accepting the various fasteners for a wide selection of prefilters. The prefilters may include Camfil Farr's 2" or 4" deep 30/30® and any of our 6" or 12" deep rigid filters. Research indicates that proper prefiltration extends the life of absolute filters 45 to 800 percent, dependent upon the level of prefiltration applied. Additionally, there is an increased emphasis on reducing downstream particle counts in spaces ranging from health care applications, to food processing and traditional clean manufacturing spaces, such as pharmaceutical and electronics industries. Good prefiltration reduces downstream particle counts in those applications, by reducing the load of particulate to which each increasing level of higher efficiency filtration is exposed. The prefilter protects the ASHRAE high efficiency filter and the high efficiency ASHRAE filter protects the absolute filter, resultant in an extended final filter life and cleaner spaces. When combined with the swing bolt assemblies, the entire bank will meet the positive sealing integrity required of the absolute filter and provide a single side, front access servicing system. 1 Durafil is only available in 12” deep configuration.



Spec Sheet
Sizes | Buy


[+] Larger

Glide Pak

[ Housings ]

• High capacity, gaseous contaminant control in a Glide/Pack® housing.
• Side-access housing integrity with dual access doors may be up to four filters high by six filters wide

Typical applications: HVAC system installation in commercial, industrial, manufacturing and medical facilities.
Construction: 16-gauge galvanized steel, gasketed dual access doors, filter track for a 4" prefilter or final filter and anodized aluminum filter tracks for CamSorb CF 1" rechargeable panels (12 per 2000 cfm), weatherproof. .
Filters: 4" deep pleated prefilter or 4" deep high efficiency final filter and 12 1" deep panels of coconut shell activated carbon or other media. .
Additional data: Out-turned, pre-drilled standing flanges to mate to other HVAC equipment. .



Spec Sheet
Sizes | Buy


[+] Larger

Magna Pac

[ ]

Camfil Farr Magna/Pack: • Is constructed of all-welded 14-gauge galvanized steel (also available in 304SST) and is reinforced with channel bracing to withstand 8.0” w.g. positive or negative pressure without compromising the filter or door seals • Includes standing flanges for mating to HVAC housings or ductwork • Includes water run-off holes to allow for rooftop or exterior installation without modification to the housing • Includes dual-access doors so filters may be serviced from either side of the housing. Mounted on pin hinges, the doors either swing open or may be totally removed for convenience of filter service • Incorporates swing bolt filter fastening assemblies with equi-bearing clamps to provide uniform filter sealing pressure. This method ensures specified filter performance by sealing each filter to leak proof specifications (recommended 50% gasket compression) • Includes high-memory door gasketing to ensure housing leak free integrity to 8.0” w.g. • Includes replaceable, adjustable, positive clamping fixtures on both doors. The door seal is recreated each time the housing is serviced • Includes a challenge injection port for absolute filter evaluation. Filters are available in efficiencies from 95% to 99.995% at 0.3 microns.



Spec Sheet
Sizes | Buy


[+] Larger

Sidelock

[ ]

The Camfil Farr SlimLine Series 41 Ducted Ceiling Module is ideal for applications where minimal installation space is available and ultra clean air is a requirement. The Camfil Farr Slimline offers: • High efficiency leak free particulate control. Available efficiencies include 95% or 99.99% when evaluated on particles 0.3 micron and 99.9995% when evaluated on most penetrating particle size (MPPS). • A low profile allowing installation in a minimal depth conserving space for manufacturing or other room components. Constructed of light weight extruded aluminum profiles and joined at the corners with Camfil Farr’s Klip-Lok™ mechanism the Slimline installs in any standard 1½ “ or 2” T-bar grid system. Seismic tabs are included. • A 41-mm filter pack, completely encapsulated in Camfil Farr’s CamPure™ polyurethane sealant. CamPure is thermally/chemically stable to ensure minimal out-gassing and maintains excellent mechanical properties ensuring high-purity air for the most demanding environments over the life of the filter. • A media configuration that is optimized through Controlled Media Spacing (CMS™ ) resulting in a lower pressure drop than other media pleating techniques. Continuous glass filament separators, encapsulated in a stabilizing adhesive, promote uniform airflow while eliminating media to media contact and fiber break-off associated with other media pleating techniques. • An adjustable diffusion disc that promotes uniform airflow over the entire filter and allows filter-to-filter air balancing. Roomside adjustment is accomplished through a port in the center divider. An additional port is included for pressure drop measurement and/or aerosol challenge introduction. • Either a 10” or 12” collar connection. The collar includes an integral continuous raised ridge to assist in securing flexible ducting. • An integral white epoxy powder-coated steel grille with 62% open area to promote proper airflow and protect the filter element.



Spec Sheet
Sizes | Buy


[+] Larger

Type 8 Holding Frames

[ ]

Type 8 Frame ~ Universal Application The Camfil Farr Type 8 filter holding frame, with a variety of fasteners, will allow the installation of various combinations of ASHRAE prefiltration and final filtration. The installation may include any, or combinations of the following: • Any 1” deep panel or pleated filter • Any 2” deep panel or pleated filter • Any 4” deep panel or pleated filter • Any 6” or 12” deep rigid filter • Any headered style rigid or pocket filter System Integrity The Camfil Farr Type 8 holding frame includes: • 16-gauge welded galvanized steel construction. • A 3/4” filter sealing flange to assure proper filter seating and sealing. • Filter centering dimples for ease of installation and to assure proper filter to gasket alignment. • Polyurethane gasketing on the frame to filter sealing surface to assure leak free performance in the most demanding of applications. • Pre-drilled holes for riveting or bolt-together installation of built-up banks. • Multiple lances for the application of various fasteners to install a wide variety of standard size air filter. The Camfil Farr Type 8 holding frame: • May be assembled in banks up to six units high and any number of units wide (flat stock vertical stiffener bars are required for banks 4 to 6 units high alternating every other filter frame). • May be applied in applications to remove water or oil mist. • May be assembled in a V-bank configuration to reduce filter face velocity



Spec Sheet
Sizes | Buy


[+] Larger

Magnehelic Gauge

[ ]

Dwyer Products has been producing a broad range of gages, measuring and control instruments for pressure, temperature, level and flow applications plus a complete valve product line. Many of the company’s products are widely recognized by their brand names, such as: magnehelic®, Minihelic® and Capsuhelic® , pressure gages; Slack-Tube® and Flex-Tube®, manometers; Photohelic®, switch/gages; Rate-Master®, Mini-Master® and Visi-Float® flowmeters; and Dwyer® pressure switches.



Spec Sheet
Sizes | Buy


[+] Larger

Pad Holding Frame

[ ]

Filtration Group Pad Holding ~ Frames make changing filters a snap. There’s less to carry to the jobsite…disposal is simplified. Pads are changed quickly, safely and efficiently. Pad and frame systems are as easy as 1-2-3: 1. Open hinged gate 2. Remove dirty pad and install new filter pad 3. Close gate Filtration Group’s permanent Pad Holding Frames are constructed of a durable 24 gauge galvanized steel frame. Filter frame is hemmed on one side for safety and added strength. The downstream side is 16 gauge 1" x 1" galvanized welded wire, spot-welded to the frame for extra support. An 11 gauge galvanized steel hinged gate provides maximum media support with no restriction to air flow. Pad and frame systems will fit into your present filtration system without modification of existing hardware. They are widely used to replace most conventional permanent or disposable type air filters. In most applications, there is no need to remove the holding frame from the channel or grid system to change the filter pad. We offer a wide range and variety of filter media’s to meet your application needs. ~ Rugged galvanized construction ~ Hinged gate makes filter change-out quick and easy ~ Wire backing is spot welded to frame for added support ~ Cost effective system ~ Filter media can be tailored to specific needs



Spec Sheet
Sizes | Buy


[+] Larger

Zip-Lok

[ ]



Spec Sheet
Sizes | Buy